Miscellaneous Parts

Western Chutes Chute Janitor™ Cleaning Control Panel green light assembly. This assembly has a 30.5mm diameter, uses a Type 4/13 incandescent light, has a green lens, and is 24VAC. UL Certification Listed E131568 and CSA Certification 68551. See...

This replacement green palm button covers the light on "W" Series chute intake doors with an electrical interlock and pneumatic system. The button screws into place at the top of the chute intake door.

Roll of 1" wide x 10’ long 18 gauge galvannealed hanger iron with holes for supporting and stabilizing horizontal discharge doors under light load conditions. To be screwed to discharge door frame or adaptor assembly and mounted to the ceiling or...

One pair 1/2"x30" hanger rods with couplings to suspend offset from deck or floor above. Installer to provide appropriate anchoring method to attach rod to deck or floor above. Hangers are to be installed at the top of the offset and at the...

One pair 1/2"x60" hanger rods with couplings to suspend offset from deck or floor above. Installer to provide appropriate anchoring method to attach rod to deck or floor above. Hangers are to be installed at the top of the offset and at the...

Roll of 1-1/2" wide x 20’ long 26 gauge galvannealed hanger strap with holes for stabilizing horizontal discharge doors under light load conditions. To be screwed to discharge door frame or adaptor assembly and mounted to the ceiling or wall as...

Bronze 1/2” flange shaft hinge bearing is used on both sides of the removable shaft hinge in most “W” series bottom hinged chute intake doors. Each door takes two bearings. See attached spec’s to verify dimensions of this product before ordering.

Replacement latch and catch for use on any “M” series Vertical Discharge Door. This latch is a an OEM direct replacement for doors requiring a single slam latch on center at the bottom of the top hinged door. When the fusible link melts the door...

High efficiency hydraulic oil in 5-gallon pails for use in any series trash compactor power pack. Used in small, one-half yard, chute fed compactors up to 10 yard behemoths as well as the hydraulics on trash trucks. Also used in chute fed...

Heavy duty long lasting hydraulic fluid suction filter for use with all Western Chutes, Compactors & Recycling Systems chute fed trash compactor and recycling systems power packs. Most compactor manufacturers recommend the filter be replaced...

Replacement bulb used in “W” Series Electrical Interlock light assemblies which is designed to last 10,000 life hours. This bulb is 1.19” long and is 120 volt/.025 amps. It has a T2-1/2 bulb shape with a BA9s miniature bayonet base. This...

Replacement bulb used in “W” Series Electrical Interlock light assemblies which is designed to last 10,000 life hours. This bulb is 1.19” long and is 24 volt/.073 amps. It has a T2-1/2 bulb shape with a BA9s miniature bayonet base. This...

Replacement key stamped with 42642 for use in cylinder locks installed in any size “W” Series Chute Intake Door keyed to this number.

One key stamped with S54F for use in "W" Series cylinder locks installed in any size “W” Series Chute Intake Door keyed to this number. Click here for the complete cylinder lock.

One key stamped with SC1 for use in "W" Series cylinder locks installed in any size “W” Series Chute Intake Door keyed to this number. Click here for the complete cylinder lock.

Replacement key for use with key-operated switch in "W" Series electrical interlock and pneumatic control panel. This key will not work with Cutler-Hammer 22mm switches.

Keyed On/Off electrical switch replaces 22.5mm switch or existing keyed on/off switch on all series trash compactor, recycling, cleaning and chute door electrical interlock control panels. Switch has a round metal operator (IP66, Type 4/13) with...

Latch assembly for “W” style foot operated chute intake doors. Includes two mounting screws and installs in the right side of a bottom hinged foot operated chute intake door. This style latch is used by almost all chute door manufacturers and...

This latch assembly is made up of the face plate and latch and has an adjustable 2-3/8" or a 2-3/4" set back from the back of the face plate to the spindle hole. The brass finish face plate is 1"x2-1/4" with a latch diameter of 7/8". The latch...

Complete replacement latch trigger assembly. Includes cast aluminum thumb trigger, machined spindle, "e" clip and trigger screw. This assembly has a custom spindle designed for doors where the latch must be held slightly lower in the door to...